LCD 1602 I2C with WeAct Black Pill STM32F411CE

Wiring for the LCD 16x2 with I2C backpack on the WeAct Black Pill STM32F411CE (STM32F411CE, 3.3 V logic), chosen with the same pin rules BoardPilot uses: default buses first, and no pins that are used for flash, USB, the debugger or booting.

Wiring

LCD 1602 I2C pin	Role	WeAct Black Pill STM32F411CE pin	Notes
GND	Ground	G
VCC	Power	5V	Needs 5 V for good contrast: use 5V
SDA	I2C data (SDA)	B7 (PB7)	The backpack pulls SDA up to 5 V. Usually works; a level shifter is safer
SCL	I2C clock (SCL)	B6 (PB6)	The backpack pulls SCL up to 5 V. Usually works; a level shifter is safer

Check before you power it on

Supply: 5 V from the 5V pin.
I2C uses the board’s default pins B7 (SDA) and B6 (SCL). Most modules include pull-up resistors; if the part is not found, check them and swap-test SDA/SCL.

Test code (Arduino)

#include <Wire.h>

void setup() {
  Serial.begin(115200);
  Wire.begin();  // SDA = B7, SCL = B6 (the board's default I2C pins)
  Wire.beginTransmission(0x20);
  bool found = Wire.endTransmission() == 0;
  Serial.println(found ? "LCD 16x2 with I2C backpack found at 0x20" : "Not found: check power, GND and SDA/SCL");
}

void loop() {}

Arduino board: STMicroelectronics:stm32:GenF4:pnum=BLACKPILL_F411CE,usb=CDCgen,upload_method=dfuMethod. To upload over USB, hold BOOT0, press and release NRST, then release BOOT0 (DFU mode). An ST-LINK on the SWD pins also works.

Questions

Which WeAct Black Pill STM32F411CE pins do I use for the LCD 1602 I2C?

GND → G, VCC → 5V, SDA → B7 (PB7), SCL → B6 (PB6).

Does the LCD 1602 I2C work with the WeAct Black Pill STM32F411CE at 3.3 V?

Yes: the LCD 1602 I2C runs at 5 V and the WeAct Black Pill STM32F411CE uses 3.3 V signals, so no level shifting is needed.

What is the I2C address of the LCD 1602 I2C?

0x20 or 0x21 or 0x22 or 0x23 or 0x24 or 0x25 or 0x26 or 0x27 or 0x38 or 0x39 or 0x3A or 0x3B or 0x3C or 0x3D or 0x3E or 0x3F. An I2C scan (BoardPilot does it for you) shows which one your module uses.

BoardPilot checks this wiring in 3D as you build it, and finds crossed or missing wires on the real board.

Download BoardPilot

Full WeAct Black Pill STM32F411CE pinout · LCD 16x2 with I2C backpack: all pins and data

The LCD 1602 I2C on other boards

ESP32 DevKit Arduino Mega 2560 R3 Arduino Nano Arduino Uno R3 ESP32-C3-DevKitM-1 ESP32-S3-DevKitC-1 Nordic nRF52840 DK NUCLEO-F401RE Raspberry Pi Pico 2 Raspberry Pi Pico W Raspberry Pi Pico Teensy 4.1

Other parts on the WeAct Black Pill STM32F411CE

BME280 BMP280 DHT22 DHT11 HC-SR04 SSD1306 OLED MPU6050 DS18B20 WS2812B LED strip SG90 servo Relay module HC-SR501 PIR INA219 VL53L0X BH1750 MAX30102 RC522 RFID NEO-6M GPS Capacitive soil moisture sensor ADS1115 TM1637 28BYJ-48 stepper L298N Potentiometer Push button LED Joystick module SD card module AHT20