BH1750 with NUCLEO-F401RE

Wiring for the GY-302 BH1750 light sensor on the NUCLEO-F401RE (STM32F401RE, 3.3 V logic), chosen with the same pin rules BoardPilot uses: default buses first, and no pins that are used for flash, USB, the debugger or booting.

Wiring

BH1750 pin	Role	NUCLEO-F401RE pin	Notes
VCC	Power	3V3
GND	Ground	GND
SCL	I2C clock (SCL)	SCL/D15 (PB8)
SDA	I2C data (SDA)	SDA/D14 (PB9)
ADDR	Not wired to the board	not connected	Address select: LOW or open = 0x23, HIGH = 0x5C

Check before you power it on

Supply: 3.3 V from the 3V3 pin.
I2C uses the board’s default pins SDA/D14 (SDA) and SCL/D15 (SCL). Most modules include pull-up resistors; if the part is not found, check them and swap-test SDA/SCL.

Test code (Arduino)

#include <Wire.h>

void setup() {
  Serial.begin(115200);
  Wire.begin();  // SDA = SDA/D14, SCL = SCL/D15 (the board's default I2C pins)
  Wire.beginTransmission(0x23);
  bool found = Wire.endTransmission() == 0;
  Serial.println(found ? "GY-302 BH1750 light sensor found at 0x23" : "Not found: check power, GND and SDA/SCL");
}

void loop() {}

Arduino board: STMicroelectronics:stm32:Nucleo_64:pnum=NUCLEO_F401RE. Plug the USB cable into the mini-USB port on the ST-LINK end. No button press is needed.

Questions

Which NUCLEO-F401RE pins do I use for the BH1750?

VCC → 3V3, GND → GND, SCL → SCL/D15 (PB8), SDA → SDA/D14 (PB9).

Does the BH1750 work with the NUCLEO-F401RE at 3.3 V?

Yes: the BH1750 runs at 3.3-5 V and the NUCLEO-F401RE uses 3.3 V signals, so no level shifting is needed.

What is the I2C address of the BH1750?

0x23 or 0x5C. An I2C scan (BoardPilot does it for you) shows which one your module uses.

BoardPilot checks this wiring in 3D as you build it, and finds crossed or missing wires on the real board.

Download BoardPilot

Full NUCLEO-F401RE pinout · GY-302 BH1750 light sensor: all pins and data

The BH1750 on other boards

ESP32 DevKit Arduino Mega 2560 R3 Arduino Nano Arduino Uno R3 WeAct Black Pill STM32F411CE ESP32-C3-DevKitM-1 ESP32-S3-DevKitC-1 Nordic nRF52840 DK Raspberry Pi Pico 2 Raspberry Pi Pico W Raspberry Pi Pico Teensy 4.1

Other parts on the NUCLEO-F401RE

BME280 BMP280 DHT22 DHT11 HC-SR04 SSD1306 OLED MPU6050 DS18B20 WS2812B LED strip SG90 servo Relay module HC-SR501 PIR LCD 1602 I2C INA219 VL53L0X MAX30102 RC522 RFID NEO-6M GPS Capacitive soil moisture sensor ADS1115 TM1637 28BYJ-48 stepper L298N Potentiometer Push button LED Joystick module SD card module AHT20