L298N with ESP32-C3-DevKitM-1

Wiring for the L298N dual motor driver on the ESP32-C3-DevKitM-1 (ESP32-C3, 3.3 V logic), chosen with the same pin rules BoardPilot uses: default buses first, and no pins that are used for flash, USB, the debugger or booting.

Wiring

L298N pin	Role	ESP32-C3-DevKitM-1 pin	Notes
ENA	Input to the part	10	Motor A speed (PWM). Remove the jumper to use it
IN1	Input to the part	3	Motor A direction
IN2	Input to the part	0	Motor A direction
IN3	Input to the part	1	Motor B direction
IN4	Input to the part	not connected	Motor B direction
ENB	Input to the part	not connected	Motor B speed (PWM). Remove the jumper to use it
12V	Not wired to the board	not connected	Motor supply 5 to 35 V from a separate supply
GND	Ground	GND
5V	Not wired to the board	not connected	5 V output of the on-board regulator (jumper on, supply up to 12 V)
OUT1	Not wired to the board	not connected	Motor A
OUT2	Not wired to the board	not connected	Motor A
OUT3	Not wired to the board	not connected	Motor B
OUT4	Not wired to the board	not connected	Motor B

Check before you power it on

Motors, servos, relays and LED strips can draw more current than the ESP32-C3-DevKitM-1’s pins or USB can give. Power them separately and connect the grounds together.

Test code (Arduino)

// Motor A: ENA = speed (PWM), IN1/IN2 = direction. Remove the ENA jumper on the module.
void setup() {
  pinMode(3, OUTPUT);
  pinMode(0, OUTPUT);
  pinMode(10, OUTPUT);
}

void loop() {
  digitalWrite(3, HIGH);
  digitalWrite(0, LOW);
  analogWrite(10, 180);  // about 70% speed
  delay(2000);
  analogWrite(10, 0);    // stop
  delay(1000);
}

Arduino board: esp32:esp32:esp32c3. If uploading does not start, hold BOOT, press and release RST, then release BOOT.

Questions

Which ESP32-C3-DevKitM-1 pins do I use for the L298N?

ENA → 10, IN1 → 3, IN2 → 0, IN3 → 1, GND → GND.

Does the L298N work with the ESP32-C3-DevKitM-1 at 3.3 V?

Yes: the L298N runs at 5 V and the ESP32-C3-DevKitM-1 uses 3.3 V signals, so no level shifting is needed.

BoardPilot checks this wiring in 3D as you build it, and finds crossed or missing wires on the real board.

Download BoardPilot

Full ESP32-C3-DevKitM-1 pinout · L298N dual motor driver: all pins and data

The L298N on other boards

ESP32 DevKit Arduino Mega 2560 R3 Arduino Nano Arduino Uno R3 WeAct Black Pill STM32F411CE ESP32-S3-DevKitC-1 Nordic nRF52840 DK NUCLEO-F401RE Raspberry Pi Pico 2 Raspberry Pi Pico W Raspberry Pi Pico Teensy 4.1

Other parts on the ESP32-C3-DevKitM-1

BME280 BMP280 DHT22 DHT11 HC-SR04 SSD1306 OLED MPU6050 DS18B20 WS2812B LED strip SG90 servo Relay module HC-SR501 PIR LCD 1602 I2C INA219 VL53L0X BH1750 MAX30102 RC522 RFID NEO-6M GPS Capacitive soil moisture sensor ADS1115 TM1637 28BYJ-48 stepper Potentiometer Push button LED Joystick module SD card module AHT20